Post Your Successful Diesel Mods At Dieseldatabase

By Dean Isaacson | Published: 7 Mar 2011

Have you completed a successful mod on your diesel truck? and did you take pictures and discovered tips that might help others? Your post is welcome here. All you have to do is register on this site. Then contact us via the the contact form on the ABOUT page (see menu), letting us know you […]

Stewart Warner B756 Standard Tachometer Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B756 Standard Tachometer Install Sheet Stewart Warner B756 Standard Tachometer Install Sheet [thanks to Stewart Warner used with permission]

Custom Fuel System

By dzljim | Published: 10 Nov 2010

Bigger injectors require more fuel. Lots more fuel than what the oem system can put out. And the OEM stuff has many faults, which just makes it that much more appealing to replace the whole darn system! I was planning on doing some work to the truck and I knew it would be laid up […]

NXD Stacker Nitrous System

By rodslinger | Published: 23 Oct 2010

SO you're on the fence about the whole Nitrous issue. Well what if there was a product out there that was mild enough for the daily driver, wouldn't break the bank to purchase and easy enough even the most novice shade tree mechanic could install it? Well here ya go – The guys at Nitrous […]

Dodge Cummins Under Hood Mods

By dieselminded | Published: 24 Oct 2010

Click picture for a full size view. Click on the product titles below for a link to a dealer OuterWears FAQs (Questions About Prefilters) Why do I need a Pre-Filter? How does a Pre-Filter work? Will adding a Pre-filter reduce my airflow or horsepower? Will the Pre-Filters work on paper filters? How much dirt will […]

Stewart Warner B764 Programmable Speedometer Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B764 Programmable Speedometer Install Sheet Stewart Warner B764 Programmable Speedometer Install Sheet [thanks to Stewart Warner used with permission]

Blue Chip Installation

By dieselminded | Published: 23 Oct 2010

Installation Directions for the Blue Chip Wizard Fuel Management System For the 1998-2002 Dodge For this installation you will need: a ratchet with extension, a 10mm socket, (17 and 19 mm wrenches for 2000 and up trucks only),a 13 mm wrench or socket, an 11mm or 7/16 deep socket or wrench, an electric drill with […]

12V Cummins Governor Lever Adjustment

By unknown | Published: 23 Oct 2010

Here is the ins and outs of the secret governor lever adjustment This is a cut away view of the governor of a P7100 pump. Notice how the lever hit the cam plate flush at the very bottom edge. To check your adjustment the throttle lever needs to be moved until the lever just touches […]

Exhaust Stack Gallery

By unknown | Published: 23 Oct 2010

  Submit Yours !!!!

Stewart Warner B754 Gauge Pods Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B754 Gauge Pods Install Sheet Stewart Warner B754 Gauge Pods Install Sheet [thanks to Stewart Warner sw-performance.com used with permission]

Another 24V Lift Pump Replacement Procedure

By Andy | Published: 23 Oct 2010

This is how I replaced the lift pump on my ’99 QC, 4×4. Not sure what variations may or may not accure on other models. Parts list…………..New lift pump, lift pump wire pig tail, banjo bolts washers (8), dielectric grease and approx 1/2 gallon of clean diesel. Tools ………. 3/8″ drive ratchet, 3 or 4 […]

Rust Prevention

By unknown | Published: 23 Oct 2010

Here’s a convenient and easy method of applying rust preventing solutions to inner panels and seams to control or avoid rust to various body seams. The nicest feature, is that you don’t have to remove interior panels to apply, just insert the feed hose into where you want to apply your rustproofing. The specific solutions […]

Cummins 12V Idle Adjustment

By unknown | Published: 22 Oct 2010

Adjusting the idle speed on the diesel engine is not difficult. The adjustment is located on the driver side of the injector pump near the rear of the pump. You will need a 10 mm wrench. Correct speed is: 1994-1998 with AT – in drive with AC on 750 -800 RPM 1994-1998 with manual in […]

Tips & Tricks for Better Fuel Economy

By Andy | Published: 24 Oct 2010

1. Air up your tires.Keeping your tires aired up to manufacturers specs can help your fuel economy up. 2. Leave your tailgate up!The tailgate up creates a vortex behind the cab which pushes air up over the tailgate. The tailgate down allows the air to push down on the bed creating drag. 3. Be easy […]

Dodge 24V IAT Sensor Cleaning

By Dean Isaacson | Published: 23 Oct 2010

This is an article for cleaning the IAT sensor on the 1998-2002 24V diesel engine. The IAT sensor measures the temperature of the intake manifold. The ECM uses this sensor reading to set injection timing and adjust the air-fuel ratio. If the fuel mileage and power output of you engine seem low, some owners have […]

CTD Dimensional Specification

By Dean Isaacson | Published: 11 Nov 2010

2002 CTD/RAM Descriptions Specification Engine Type In-Line 6 Cyl. Turbo Diesel Bore & Stroke 102.0 X 120.0 mm 4.02 X 4.27 In. Displacement 5.9 L 359 Cu. In. Compression Ratio 245 HP 2002 CTD 235 HP 2002 CTD   17.0:1 16.3:1 Horsepower A/T M/T   235 @ 2700 RPM 245 @ 2700 RPM Torque Rating […]